Death Over Life in Flauberts Madame Bovary Essay -- Madame Bovary Ess

Death Over Life in Flaubert's Madame Bovary      Ã‚  Ã‚   Often in literature, a character is found that is quite memorable. Never was this more true than in Flaubert's Madame Bovary. To some, Emma Bovary's action at the end of the novel was drastic and unnecessary; others believed her death to be the end of the natural progression of the story. However, Emma's decision to commit suicide was relatively simple, yet came as a last resort. She had exhausted all the other options she felt were available, and in the end made her plan based on finances, lost love, and the sheer boredom of her life.    One motivation for Emma's suicide was her financial problems. She spent extravagant amounts of her husband, Charles', money on dresses, scarves, and house decorations. More money was expended for Emma's "music lessons," which were actually her alibi for her affair with Leon. Also, she had spent too much money while preparing to run off with Rodolphe, a journey that never occurred. All Emma's debts piled up, then came due at the same time; she tried to put them out of her mind, to no avail. She even went as far as to beg money from Rodolphe, her former lover, who rejects her. After leaving Rodolphe Emma is angry; she has lost her normal ability to reason, but could still make a decision (Roe 42). As she could not forget, she devised, in a moment of "Emma-style logic," the solution to her problems. So, "...in an ecstasy of heroism, that made her almost joyous, she ran down the hill...and reached the chemist's shop" (Flaubert 221-222). Once at the chemist's, she frantically ingests a lethal dose of arsenic. It is tragic that the only release from her problems Emma could see was death.    Emma's failed love af... ...cide became her only option, and having taken the action she thought necessary, "...she went home, suddenly calmed, and with something of the serenity of one who had performed a duty" (Flaubert 222). However, Emma's death was not serene; it was violent and grotesque. Ironically, she did finally achieve "tragic romance heroine" status: she died young, penniless, and heartbroken.    Works Cited Buck, Stratton. Gustave Flaubert. University of the South: Twayne. 1966. 68-72. Flaubert, Gustave. Madame Bovary. New York: Dover. 1996. Green, Frederick C. French Novelists: From the Revolution to Proust. New York: Frederick Ungar, 1964. 233. Roe, David. Gustave Flaubert. New York: St. Martin's, 1989. Turnell, Martin. "Madame Bovary." Flaubert: A Collection of Critical Essays. Ed. Raymond Giraud. Englewood Cliffs: Prentice-Hall, 1964.   

Women and the Effect of Industrial Revolution

The industrial revolution was a great time of change for men, the economy, domestic life, and brought the change in the role of women in society to the forefront. As time evolves, so must the lifestyles we as a society lead. This was no different during the industrial revolution in Britain and France. Throughout this paper I will begin to discuss how the impact of industrialization effected the switch in labor from domestic to factory, the new role of the mother in an industrialized family and the issue of education in the lives of ordinary people, as discussed in the memoirs we have read in class. One of the main effects of industrialization was the switch in labor from the women working at home in a domestic environment to that where her labor brought in wages to the family. Suzanne Voilquin speaks of this in her memoirs â€Å"A Daughter of the People†, â€Å"And so, at the end of the first week, we were very proud to to deposit on our father's mantle piece the eighteen francs we earned as wages.†(Voilquin, 112). Throughout her story, she tells of how through the ability of her and her sister being able to work, they were able to support the family while her father was infirm. Without this opportunity, the family may have been put out onto the streets. It is through these two women's effort that the family survived. With the women now being able to earn wages out of the home, the role of the mother greatly changed within the home of the industrialized family. Before the revolution, children were raised on the plantation with the mother, father, and siblings as discussed in Agricol's, â€Å"Memoirs of a Compagnon†. â€Å"[In regards to his father's plantation] moreover he made good use of his children's labor. He wanted to make us hard workers rather than gentlemen and ladies, and in this he did right.†(117). We have also learned form this era that when women moved to factories, newborn children no longer had the opportunity to reside with the mother. Infants were sent off to a wet nurse, so that the women could return to work as soon as possible after the birth. This provided a new environment in which children were raised; however the pro's and con's of this new lifestyle varied. This brings me to my final point of the issue of education in the industrial revolution. It seems that throughout the memoirs the common theme is that labor was valued over education. Most children had no education at all and went to the factory as soon as they were able, while children who had a little schooling rarely went beyond the third grade. Jeanne Bouvier speaks of this in â€Å"My Memoirs†, â€Å"[after her first communion] ‘It's a shame you cannot leave her longer. She's very gifted. She even works hard when it comes to manual tasks'.†(34). It is shown here that girls were not inferior to boys and were just as capable in school. This did nothing for the stigma that was already set on women. Many times the father was not willing to pay for his daughter's to go to school; just the sons were worthy of the cost of education. â€Å"My mother†¦paid the fees for her daughters with the money she earned†¦my father paid only for his sons.†(Perdiguier 119). Obviously, the emphasis was placed on manual labor during this revolution, for it brought in money that the family may so desperately need. The industrial revolution placed the ordinary worker into a mirade of new, enterprising, and yet sometimes compromising situations. Workers were faced with new problems, but also with opportunities that had never been available before. It is through their struggle that we are the society we know today. It is through the past that we can mold our future.

Limiting the Extent of Party Discipline in Canada Essay

Party solidarity and cohesion have always been an integral part of the Westminster Parliamentry system. The leaders of the political parties of the Canadian House of Commons , with the assistance of ‘whips’, very strongly discipline their party members to vote on issues as a single entity, especially in plenary sessions (Olson, 2003). Although, some degree of party discipline is essential for any political party to maintain their power as they require the confidence of the majority of the legislative branch of the government, this practice does not really reflect a democracy. This paper argues that implememnting a large extent of party discipline undermines the spirit of democracy as the politicians become more concerned with appeasing their party leaders for their personal benefits, instead of truly representing the desires and demands of the citizens of their respective constituencies. As mentioned previously, it is argued that strict party discipline is necessary to ensure that the current governnig party maintains its power since a vote of non confidence in the House of Commons can ultimately lead to federal re-election, or re-appointment of the prime minister. However, as Kilgour et al. rgue in Crosscurrents: Contemporaty Political Issues (2013: 205), enforcing strict cohesion strategies to ensure party unity leads to members of Parliament to become extreamly passive as they no longer think for themselves, but merely conform to the demands of their party leaders. Their opinions and thoughts are constrsained by a fear of a loss of majority in the House Of Commons. It is very crucial for any political party to value and respect the opinions of its members to assess a situation more closely and obtain diverse opinions. However, strong party discipline stifles the values and opinions of individual members of party. Consequently, this diversity of imagination is replaced by a single unit of party that reflects a single, rigid opinion on most issues. This devalues the sense of liberty and freedom that is cherished by democracy. Often times, it is observed that the members of a party vote in a similar fashion, not just to ensure a majority confidence motion, but also to derive personal gains. If a member of parliament wishes to advance their political career and gain quicker promotions, he or she muct act according to the command of their party leaders (Kam, 2006). Expression of dissent from the MPs can have dire consequences for their career. They can be warned about the lack of financial support, or even be ultimately expelled from the party caucus. Kam (2006) also suggested that the promotion of ministers is greatly manipulated by the prime minister to ensure maximum conformation to the party’s position. Sometimes, certain ministers of parliament are deliberately brought into the cabinet as it is too dangerous to leave them as a backbencher (a member of House of Commons) where they can openly challenge and vote against the position of the leader of the political party. This suggests that the deliberate promotion, or demotion, ministers of parliament is not due to their, merits or demerits, but is rather strategically devised to overall benefit the party. In addition, the vote of the members of the House of Commons not only does not represent the opinions of individual ministers, but also it not a representation of a member’s unyielding and unconditional loyalty to his or her party. Rather, it is a conscious decision to vote according to the wishes of the party leader to maintain the imge of conformity and ensure personal gains and benefits for the members of parliament, which would reward in the form of more opportunities to ascend the political ladder and make personal and professional gains that do not particularly benefit the citizens of the consituency that elected the member of parliament. It is unquestionable that voting in the Canadian House of Common is extremely disciplined and very highly regulated by emloying various methods. The study of the patterns of recorded votes shows that majority of votes show almost no dissent from the party members. Also, rejection of major government motions due to dissent of the members of the House of Commons is extremely rare (Malloy, 2003). Canada operates on a system of majoritarian parliamentary government. Cohesion of political parties is very essential to maintain a majority rule by ensuring that vote of non confidence is not ever issued (Kam, 2001). Due to this constant threat of the possibility of loss of majority and formation of a coalition, political parties are very strongly disciplined by their leaders. A coalition governmet is not necessarily always detremental. It can help to foster more cooperation in different political parties and compel the members of a party to consider the opinions and views that are different from the ideology shared by their party. It also provides an opportunity for a greater debate and consideration before arriving at a common decision. Maintaining strong party discipline just to eliminate the possibility of the formation of a coalitions limits the possibilities for political experimentation and possible positive growth. The change is not just welcomed, but also deliberately resisted using the traditional practice of oppressive party discipline. The members of parliament are elected by, and are required to respresent the citizens of their respective constituencies. The common vision shared by their party and party leader may or may not reflect the wishes of the citizens. The first and foremost duty of an MP is to cater to the needs and the demands of the citizens who democratically elected him or her. The loyalty to one’s party should be a secondary priority. However, as observed, most times, this is not the case. This severely debilitates the sole purpose of a democratic government which demands the citizens’ voice and opinions to be heard above all others. Although some degree of party discipline may be required to control and maintain cohesion within the House of Commons to propose policies and arrive at a firm decision, it does not really encompass democratic ideas. Party discipline compells the members of a party to not pay heed to the needs of the citizens, but to blindly follow the demands made by their party leaders. This practice is also morally questionable as the political success of ministers of parliament is largely based on their loyalty to the party’s alues, even if they contradict his/ her personal opinions. Instead of being constantly threatened by the possiblity of losing the confidence of the majority of the House of Commons, fundamental changes need to be made to change the Westmister Parliamentry structure to alter, if not eliminate, this system that makes it almost mandatory for the parties to implement rigid party discipline. Limiting the extent of the party discipline would help to make the Canadian government more democratic by accomodating more diverse ideas and opinions.

Impact of wireless communication devices and systems nowadays Essay

ABSTRACT Nowadays, wireless communication devices and systems have a huge impact on everyone. This project describes the performance of the 433MHz RF module for WSN applications. The system is built wirelessly where it can transmit and receive signals from DHT11 which is a temperature sensor and humidity. This 433MHz RF module is used to transmit and receive data from Arduino Pro, which is connected directly to the RF module and sensor modules. It also allows data packets to be moved remotely. There are other transmissions such as Wi-Fi, Zigbee, Bluetooth and others but the 433MHz RF module creates more flexibility in dealing with such problems. Therefore, the 433MHz RF module is selected to achieve the goal of the project as the RF module can handle the problem. Additionally, the transferred data will also be sent and received without any loss of data in the barrier or in a line of sight. These projects should examine the distance and performance of the 433MHz RF module. ABSTRAK Pada masa kini, peranti dan sistem komunikasi tanpa wayar mempunyai impak yang sangat besar kepada semua orang. Projek ini menerangkan tentang prestasi modul RF 433MHz untuk aplikasi WSN. Sistem ini dibina secara wayarles dimana ianya boleh menghantar dan menerima isyarat dari DHT11 yang merupakan sensor suhu dan kelembapan. Modul RF 433MHz ini digunakan untuk menghantar dan menerima data dari Arduino Pro, yang disambungkan secara langsung dengan peranti modul RF dan sensor. Ia juga membenarkan paket data yang diperlukan untuk dipindahkan dengan jarak jauh. terdapat jugak penghantaran lain seperti Wi-Fi, Zigbee, Bluetooth dan lain-lain lagi tetapi modul 433MHz RF mencipta lebih banyak fleksibiliti dalam menangani masalah seperti ini. Oleh sebab itu, 433MHz RF modul dipilih untuk mencapai matlamat projek ini kerana modul RF dapat menangani masalah tersebut. Selain itu, data yang telah dipindahkan juga akan dihantar dan diterima tanpa ada sebarang kehilangan data di dalam halangan mahu pun garis penglihatan. Projek-projek ini perlu mengkaji mengenai jarak dan prestasi modul RF 433MHz. DEDICATION To my beloved parents, thank you for the support, encouragement, and understanding from both of you, Mukhtar Bin Baharom and Rahmah Binti Yunus. This work is dedicated to them. Acknowledgment Thanks to Allah S.W.T for his blessing and mercy for giving me the strength to complete my task that given in Final Year Project. However, it is impossible for me to complete this project without help and support from anybody. So, I would like to thank you for all of them. I would like to express my deep gratitude to my supervisor, Mr. Mohd Khanapiah Bin Nor for guiding me to complete this project. He was giving me necessary information regarding the project and a lot of inspiring ideas. My appreciation also gives to my beloved parents, family members, and friends who have been behind me throughout this project for the encouragement and supported from them. I really appreciate all their help and support while I’m completing this project. Lastly, I would like to sincerely thank Universiti Teknikal Malaysia Melaka (UTeM) for providing the facilities and equipment for me to complete my project. In the previous era, the technology application mostly using wire but now a wireless device has become commonplace. The wireless sensor network can be defined as an application that having no wires connection on that devices. In addition, to make the system easy to monitor from a distant location, the RF 433MHz module was used. So, this project gives the idea for studying details about the RF 433MHz module performance for WSN application. 1.1 Project Background Nowadays, using the wireless sensor network (WSN) technology to monitor the environment helps someone to solve the problems of deployment difficulty, high cost, and realized unmanned monitoring which is mostly used in a factory, buildings, laboratory, and house. This project is to study the range and performance of the RF 433MHz module for WSN application. RF 433MHz module is popularly used in the remote control system. This range also available to use in this area. There are two types of the RF module which is transmitter and receiver. From research, using RF 433MHz module, the data can get more accurately without any data losses with the range that given than compared to another transmission for the wireless sensor network. The range that can reach by this RF module is different between outside and inside area. For inside area, it can work for 50 meters through multiple walls with an antenna, while for the outside area, it will be able for hundreds of meters. Besides that, a microcontroller such as Arduino also used in this project. Arduino that available for this project is Arduino PRO which is it has 3.3V port that will be easier to connect directly to the types of RF 433MHz module that used in this project. This project also will be studied the analysis of the data transmission by giving a few of distance between the transmitter and receiver of the RF 433MHz modules when located in the obstacles or line of sight area. Then, the data that are received will be displayed on the computer whether there are data losses or not. The problem that becoming as issues right now is there is a lot of ways to send data but the problem is about the range, cost, and data losses. So, for this situation, study the performance of RF 433MHz can overcome the problem for the WSN application. The objectives of this project are to understand the range and performance of RF 433MHz module. Moreover, exploration about the transmitting and receiving the data by using the RF 433MHz module. The main work scope of this project is to make sure this project will achieve the objectives. The main focus of this project:- i. To study and understanding the range of RF 433MHz module. ii. To transfer data by using RF 433MHz module. 1.5 Methodology In this project, there is three part that needs to follow. For the first part, it will be focused on the conducting the literature review and do some research more detail about the RF 433MHz module. Meanwhile, for the second part, after the software development process, the hardware development process will take over and include the testing of the project. Last part, when the hardware and software complete their part, it will be followed by testing the performance and the operation of the project to make an analysis. The methodology is the explanation of the procedures or steps when doing this project. The simulation, analysis, and evaluation of the project. A literature review is an important step before proceeding to the project. Collecting all the required information about the 433MHz RF module from the books, journals, and website. The literature review also can provide a useful information to complete the project. The idea for this project comes from the problem faced when the data that have been transmitted becomes losses with the range that provided. In this chapter, it will be explained more details about the project and also the components that will be used in this project. The frequency of 433MHz that used in the wireless sensor network can test the sending and receive the data for this range without any data losses. 433MHz RF modules required the 17cm of the antenna to support the range to send the data. The range is one of the most important parameters of any wireless system which is it defined how the transmitter and receiver can be apart from each other to send the data. A range of the outside with few obstacles the data can go through hundreds of meters. While for the indoor, the data can go over 50 meters through multiple walls. The external antenna will be soldering to the â€Å"ANT† on the transmitter to get more range which is 17cm of the length of the antenna that was used. Regarding the several research that I have done from a few of journals that can relate to my project. Wireless sensor networks are currently widely used in several of monitoring and control applications. Guohua Yang and Kui Zhang (2015) have conducted a project regarding the 433MHz radio for long-range communication. They present about the connectivity, range of the communication and packet loss ratio that have been performed in the indoor and outdoor environment. The Maarten Weyn and Glenn Ergeerts (2013) conducted the survey of the DASH7 Alliance Protocol for wireless sensor network (WSN). In this research, it stated that 433MHz is an unlicensed band. They said that, due to the frequency, it has a better propagation characteristic opposed to the higher frequency. The wavelength at the center of frequency is 69.14cm which is the bandwidth for the frequency is 1.84MHz. This limits the data rate of the communication at this frequency 433MHz is an ideal for low power of low data rate communication. Budi Setiyono, Sumardi, and Rafdito Harisuryo (2015) have conducted a project on measurement system of temperature, humidity and air pressure over 433MHz radio frequency for an application on a quadrotor. They using the telemetry system which is the measurement process of data at a certain distance. Then, they stated that data will be processed or analyzed by the receiving station. They stated on their result which is for successful transmission, the amount of data that received will be same as the amount of data that have been sent. This project is to improve the data transmission with 433MHz RF modules either in obstacles or line of sight condition. The 433MHz RF modules are categorized as the lower cost, lower power consumption and the most important is when the longer the distance for data that transmit remains accurate when it received by the receiver. In theoretical, the success of data transmission is the amount of data received will be same as the data that have been sent. That means there are no data losses when the transmission occurred. Radio Frequency (RF) is a rate in the range of around at 3 kHz to 300GHz which is corresponding to the frequency of radio waves, and the alternating current that can carry the radio signals. ITU bandstand for International Telecommunication Union that defined for the electromagnetic frequencies that used for radar and radio. The best set of terms for frequencies used in communication. While the very lowest bands have no radar applications. The table below shows the frequency range and ITU band. The Arduino Pro is a microcontroller board based on the ATmega328. This microcontroller is an open-source hardware and software. The version that used in this project is 3.3V/8MHz. This version can be powered by a battery or external power supply. It has 14 digital inputs and output pins which is 6 of it can be used as PWM output, another 6 pins for the analog input, battery power jack, an ICSP header and reset button. Arduino Pro needs to connect with FTDI cable through six pins header to provide the USB power and have a communication with the board. Arduino Pro has the port for 3.3V that can supply the voltage for the transceiver. Each of the 14 digital pins on the Arduino Pro can be used as an input and output which is operated at 3.3V. Each of the pins can provide or receive a maximum of 40mA and has internal pull-up resistor (disconnect by default) of 20 until 50 kohm. The ATmega328 has 32KB and running 8MHz of the external resonator. It also has 2KB of SRAM and 1KB of EEPROM that can read and written with the EEPROM library. The operation of the Arduino microcontroller is based on the connection made on the pins. The application can be done by using the Arduino software where Arduino function can be edited according to the applications in this software. This software can work on by using the C or C++ language. The program that has been creating the need to upload to the microcontroller by using the USB cable. If there is an error detected on the program, it will be adjusted by editing to make a correction on the process and then the program needs to reload again. Other than that, there is another option which is using the reset button to delete all the previous program that have been upload before this to make it clear then built again. MHz RF Module version that has been used. It is because can operates in the unlicensed ISM (Industry Science and Medicine) radio band. It’s available for use in the inexpensive area for short-range wireless networks of sensors. This types can operate on the 433MHz frequency and can capable of transmitting at up to 100mW and up to 300kbps. When increasing the transmit power and reducing the data rate it can maximize the range of the 433MHz. DHT11 is a digital temperature and humidity sensor. Its suitable for my project that only needs to read the data about the temperature and humidity only. Micro-B is the smallest USB connector type. This type also used for the android as a cable for charging while USB port A is that can connect to PC or laptop. This USB cable needs to connect the RF transceiver module with the Arduino Pro at the transmitter and receiver. Using this board because the standard FTDI board cannot supply the enough current to run the RFM69 433MHz RF Modules. The difference between standard FTDI and Beefy 3 FTDI is the current that can provide which is standard FTDI provide 50mA while Beefy 3 FTDI provides up to 500mA. This chapter will be discussed the procedures and steps that used in this project. Each of the methods that were used to achieve this project will be stated and explain briefly. The purpose of the methodology is used to achieve the objective that has been stated. 3.1 Software Design In this part, the software design is part to do the programming by using the Arduino software. The flow of the data transmission starting from the reading of the temperature and humidity by using the DHT11 sensor. Then, the data will be processed by a microcontroller. It will be sent through the transmission of data by using the 433MHz RF transmitter module. When the power supply is turned on, the 433MHz RF receiver module and the microcontroller ready to accept the data that have been transmitted. After that, the data is sent by the Arduino microcontroller via a serial port to the computer for displaying the data. Based on Figure 1 and Figure 2 it showed the flow how it works. Hardware design consists of two parts which are from here it will be explained how the flow of the project will be complete. For the first part as shown in Figure 3.3 is the data obtain from the DHT11 sensor reading, then the data will be transmitted by the 433MHz RF transmitter modules. While for the second part as shown in Figure 3.4 is the data received via 433MHz RF receiver modules then sent by the Arduino PRO that connected to a computer for display. The generated data for this project should be the same with the theoretical results. Besides that, the results of this project will be compared with the theoretical results, the journals or book that have been found.

Response paper Movie Review Example | Topics and Well Written Essays - 250 words

Response paper - Movie Review Example Fundamentally, Brown diverts from the conventional and template introduction common in many speeches. The relaxed and playful way of presenting her speech keeps the audience strongly gripped in her story. The employment of humor is essential in seeking the attention of the audience (Verderber, Sellnow, & Verderber, 2012). Brown’s masterful and humorous delivery of the speech has arguably held the audience together. Similarly, the positive smile and use of visual elements has enabled Brown to deliver the message to the audience. Brown has masterfully alternated between the main points and the personal stories. The speech depicts the significance of tying stories to major points, as well as, insights. The stories support and relate to the primary message. Similarly, Brown does not fear being authentic, and narrates her struggles in her research about vulnerability. Authenticity seeks to change the speaker-audience dynamic, and the listeners can feel the speaker is talking with them (2012). Although the talk was very informative, Brown needs to minimize the gestures. The gestures were too much, and can be a potential

Intercultural Organisational Management Essay Example | Topics and Well Written Essays - 1500 words

Intercultural Organisational Management - Essay Example However, majority of organizations have been confronting issues in this regard due to a number of reasons and factors (Landis & Bhagat, pp. 23-29). For this reason, this paper is an attempt to identify some of such issues while carrying out analysis of two different scenarios that will enable a comprehensive understanding of intercultural issues in the organizational management. Briefly, in the first scenario, an organization tried to introduce and implement a performance reward system in Ecuador after its successful outcomes in Netherlands for the past two years. The company sends one of their HR consultants to Ecuador to arrange briefings of the new system to the employees working there, as the system earlier enabled the organization to achieve five percent increment in productivity, as well as enhancement of employees’ morale. However, few things go wrong in Ecuador, and the HR consultant had to take flight back home without implementation of the new performance reward system. Brief analysis has facilitated the researcher to acknowledge existence of cultural dimension of Geert Hofstede (pp. 24-39) in this scenario due to issue of cultural differences in this scenario of international business. One of the major problems of this scenario was ‘Low PD’ status of the Ecuador Company, whereas, Sandra was considering it a High PD company tha t caused problems. Although on a factual basis, the system might sound very promising, however, analysis of the scenario has indicated that some problems on both sides did not allow the organization to achieve the same results of Netherlands in Ecuador. The foremost factor seems lack of awareness about the two cultures that became the biggest barrier in this process. In the past, HR managers were responsible for enhancing motivation level of employees to achieve the productivity target through bonus and reward programs (Ferraro, pp. 56-61); however,

EXAM QUESTIONS FOR RESPONSIBLE BUSINESS UNIT Essay

EXAM QUESTIONS FOR RESPONSIBLE BUSINESS UNIT - Essay Example Various Methods of Waste Management Waste management deals with reducing waste through sustainable production of goods. This sustainability can be achieved through product design and process design. Production notions need to be changed to reduce waste. There are various methods of waste management, including product life cycle management, dematerialisation and industrial eco-management and through eco-friendly designs and eco-technology. Design phase of a product offers maximum possibility of managing waste. Latest Manufacturing Industry Trend A change in trends has been seen in manufacturing industries for attaining sustainable manufacturing by changing from end-of-pipe solutions to centring on product life-cycles for integrating strategies and systems to achieve environmental sustainability. The trend is increasingly shifting towards closed-loop circular manufacturing systems and for new business models (OECD, 2009). Preference for Environment Management Systems for Waste Control Businesses are going for Environment Management Systems (EMS) – integrated environmental strategies and management systems. Application of EMS ensures that environmental issues such as waste management are looked after through enforcement of programmes to achieve related goals, which are inspected for attaining performance level, rectifying problem areas and reviewing of systems for incessant improvement. Dematerialisation for Waste Management Another trend to control waste is dematerialisation wherein resource intensity of products and processes is cut down. It is the reverse end of the scenario for waste management. It is related to reducing and bettering the standard of the resources used in production of goods and services. Dematerialisation can be achieved through reduction in product size, weight, packaging, by increasing product life and variety of uses. Industrial Ecology for Waste Management Industrial Ecology (IE) can yet be another huge step towards waste control, wherein a firm’s by-products can be used by another firm as raw material, thus, reducing resource use and waste creation for the system overall. It offers a dynamic transformation in waste management from simply reducing waste from a specific function or location, to reducing its production at the bigger scale and level of the system as a whole. Role of the Government To analyse the measures taken by the government to manage waste, the government has released the document on Waste Strategy for England 2007. There has been a UK law promulgated from Packaging and Packaging Waste Directive on the Packaging (Essential Requirements) Regulations 2003, the Producer Responsibility Obligations (Packaging Waste) Regulations 2007. Further, the government has made it legal to take all possible measures to keep waste less hazardous. It is the legal responsibility of all manufacturers, importers, stockists, logistics, disposal and managers of waste under the Duty of Care Regulations. There has been the provision on landfill tax, which is controlled by HM Revenue and Customs and presently charged ?72/tonne (+VAT) for Active waste and ?2.50/tonne (+VAT) for Inactive waste. Evaluation of NEXT Plc on Waste Management Testing Next Plc on the above theoretical frameworks, as per the NEXT CSR Report 2012, the Company has been successful in 10% additional waste recycling relatively the previous year. Overall, it is using 85% capacity of recycling functional waste.